Repair of washing
machines Zanussi is a common occurrence.
Despite the fact that these cars go off the assembly line under the sign of a
foreign brand, they can also break. And often the manufacturer is not at all
involved in the fact that the machine broke too early.
factors and improper operation are the more likely causes of the failure of the
of Zanussi washing machines. Using the statistics of service centers, you can quickly
understand which components and parts in the device of the Zanussi washing machine
are the most vulnerable.
of parts on water quality. By the way, this is characteristic not only for the Zanussi brand, but
also for other cars. Oversaturated salts with strong heating, scale deposits on
the heater and other elements.
the water in Israel is clean and transparent, all the same, the filtration
systems of the machine can become clogged with dirt and rust over time. As a
result, the typesetting and drainage system suffers. The machine stops working,
thereby upsetting its owners. At this moment it is very important to turn to
specialists in your field, to the technicians of our service center in
Jerusalem. Any repair of Zanussi equipment is within their power.
blocker. This is
already the fault of the manufacturers: both the blocker and the sensor are
slightly unfinished, therefore they break more often than other types of SMA.
(TEN) quickly fills with a scum. Experts believe that this is also due to the
fact that manufacturers lost in the selection of components from which the
tubular part of the heater is made.
belt. It is not
reliable, so every 3 months the experts of our service center advise checking
its tension and integrity. If you see signs of a stretch or damage to the belt,
tightening or replacing the assembly is required.
good thing is that you can determine the malfunction on time, as the “smart”
Zanussi automatic washing machine notifies the user of problems using fault
codes for washing machines Zanussi.
the Zanussi washing machine produces the following error codes: E11, E12, E21,
E22. Consider the most common combinations.
Problem E11. No
washing water. Most often, the code lights up if the valve that supplies water
from the water supply to the machine is shut off. The pressure in the pipe may
also be weak. Clogged filter mesh on the intake valve. Just call the repairman
and ask him to check the integrity of the hose, clean the filter. It is
advisable to check the resistance of the valve coil – a serviceable element
will give an indicator of 3.8 kOhm. All these manipulations are performed by a
washing machine repair technician. A person who is not versed in technology can
harm your typewriter, so only contact professionals. In Jerusalem, the Zanussi
washing machine repair expert is our center. We provide a guarantee of 6
months, we provide discounts to pensioners, high-quality and quick repairs
on-site and polite specialists. Contact us, you will be pleased with the
E12– Problem with water filling during
drying. If the cause is the water inlet valve, the code will appear on the
display 10 minutes after the start of the wash cycle.
E21 Water does not leave the system –
this means that the drain filter needs to be cleaned and the nozzles checked
for blockages. It is also necessary to check the operability of the impeller of
the pump – it should rotate freely in both directions. If travel is difficult,
a pump replacement is required.
E22 Indicates low drainage during drying.
You may need to clean the capacitor. Troubleshooting typical Zanussi machines.
failures should be trusted only by a professional. Zanussi Washing Machine
Repair Service Center in Jerusalem is a professional in eliminating blockages.
filter – the perfect operation of the entire washing machine. All filtration
systems need to be cleaned periodically. If you neglect this rule, then
subsequently problems can not be avoided. If clogging occurs in any of the
filters, problems arise with the intake or discharge of water.
In Zanussi, the filling filter is most often
to do to normalize the operation of the machine?
unscrew the inlet filter – it is located on the water pipe.
If you did
not install such a filter, then you need to clean the filter mesh.
Experts advise installing an inlet filter on the pipe with a special filter
cartridge that softens the water.
clean the filter mesh, proceed as follows:
connection point of the water intake hose to the machine body.
the top cover of the CM to unscrew the valve and filter.
the filter and rinse it under the tap.
Reassemble everything in reverse order.
The horizontal loading of the Zanussi washing machine is different from the
front design, but the filter is cleaned in the same way.
way, pollution can accumulate not only due to “errors” in the water supply
system, but and because of the very clothes that you send to the drum. With too
dirty things, sand, dirt, debris, threads penetrate into the machine systems.
drain filter, craftsmen often find small coins, seeds, hairpins, crumpled
checks. All this “nonsense” can provoke a halt to the work.
Important! Remember to clean the filter at
least once every 3 months. And better entrust it to the masters of their craft.
Call the service center!
of the lock for washing machines Zanussi.
problem with UBL is a frequent malfunction of the Zanussi Aquacycle SM, but it
also occurs in other models: for example, Zanussi Easyiron.
difficult to say right away why the blocker breaks – through the fault of the
manufacturer or user negligence. But there may be problems with the control
board – then the blocker has nothing to do with it.
plastic components of the hatch blocking device are unreliable and may break
even if you simply slam the hatch with force. The metal hook will survive, but
due to damage to the UBL, washing will still be impossible.
The lock is
usually not repaired – it is easier to replace it with a new one. By typewriter
Zanussi UBL costs about 1,500 rubles. It’s a little expensive, of course, so
you should first remove the old lock to make sure that it is broken. Such
repairs can only be done by experienced Zanussi washing machine repair
technicians. It is very important to replace defective parts with original
device of the repair technician removes according to the following scheme:
Opens the door.
* On the
right you will see a small hole for the locking hook, and next to the two
screws that hold the UBL. * Unscrews the fasteners.
the sealing gasket (cuff). It is held by a wire clamp that runs in a circle
along the entire gum. Pick it up with a thin screwdriver and remove it. Then remove
the cuff – do it with your hands, without a tool, so as not to damage the
the blocker by disconnecting the wires.
* Perform a
visual inspection of the device and verify the integrity of the plastic part.
If the plastic is broken, and the plates jumped out, take the device with you
and go for a new one.
* Show UBL
in the store so that you are sold exactly the same.
the lock in the reverse order.
Carefully close the hatch until it clicks, pushing it from the edge to extend
the life of the device.
the heater in a Zanussi machine.
As we said
above, the heater is one of the most vulnerable places in any washing machine,
especially Zanussi. A washing in such a breakdown may give an E05 error, while
the water in the tank stops heating.
repairs yourself, you will have to disassemble the SM case a little:
1. Turn the
machine with the front wall towards you.
the screws from the panel to remove it.
3. At the
bottom of the tank you will see the heater shank – there are 2 contacts and
wires coming from them on it.
resistance with a tester. If the device displays a value close to zero, the
heater will have to be changed. The readings of a working heater will be 20-40
5. To remove
the heater, unscrew the nut located in the center of the shank.
Disconnect the wiring going to the heater.
5. Make an
effort to get the heater from the groove. If there is a lot of plaque on him,
then he could become sticky. Take WD-40 grease and sprinkle gaps lightly. Shake
the old heater and pull it towards you.
6. Clean the
7. Install a
new heater, connect the wiring.
the back panel and start the test wash. If the water heats up, and the E05 code
is gone, then you did everything right.
Choosing the heater for the Zanussi washing machine, buy only original parts.
Do not take cheap Chinese counterparts – they will not last you long. Our
service center in Jerusalem provides only genuine parts! An improper heater can
also provoke a breakdown of the control unit, and then the repair will
definitely “fly into a penny”.
caused by the drive belt are accompanied by the fact that the motor in the
washing machine does not stop working, but the drum does not rotate. To check
the integrity and position of the belt, proceed as follows:
* Remove the
back cover by unscrewing the mounts.
* In a niche
you will see a drum pulley on which a belt should be worn. The electric motor
pulley is much smaller, it should also have a belt.
* Adjust the
belt if it has shifted. If the drum does not rotate and the belt is in place,
then a replacement is needed. After adjusting or installing a new belt, replace
the panel and start the test wash.
can see, the repair of Zanussi washing machines is to eliminate typical crashes
you not to touch the electronics. Even if you have a Zanussi washing machine
circuit, to repair or replace an electronic module, you need special tools and
relevant knowledge and experience. Do not want to provoke additional damage –
trust the master of complex problems.